postio(1) User Commands postio(1)NAMEpostio - serial interface for PostScript printers
SYNOPSISpostio-l line [-D] [-i] [-q] [-t] [-S] [-b speed] [-B num] [-L file]
[-P string] [-R num] [file...]
/usr/lib/lp/postscript/postio
DESCRIPTIONpostio sends files to the PostScript printer attached to line. If no
files are specified the standard input is sent.
OPTIONS
The first group of options should be sufficient for most applications:
-D Enable debug mode. Guarantees that everything read on
line will be added to the log file (standard error by
default).
-q Prevents status queries while files are being sent to
the printer. When status queries are disabled a dummy
message is appended to the log file before each block
is transmitted.
-b speed Transmit data over line at baud rate speed. Recognized
baud rates are 1200, 2400, 4800, 9600, and 19200. The
default speed is 9600 baud.
-B num Set the internal buffer size for reading and writing
files to num bytes. By default num is 2048 bytes.
-l line Connect to the printer attached to line. In most cases
there is no default and postio must be able to read
and write line. If the line does not begin with a / it
may be treated as a Datakit destination.
-L file Data received on line gets put in file. The default log
file is standard error. Printer or status messages that
don't show a change in state are not normally written
to file but can be forced out using the -D option.
-P string Send string to the printer before any of the input
files. The default string is simple PostScript code
that disables timeouts.
-R num Run postio as a single process if num is 1 or as sepa‐
rate read and write processes if num is 2. By default
postio runs as a single process.
The next two options are provided for users who expect to run postio on
their own. Neither is suitable for use in spooler interface programs:
-i Run the program in interactive mode. Any files are sent first
and followed by the standard input. Forces separate read and
write processes and overrides many other options. To exit
interactive mode use your interrupt or quit character. To get
a friendly interactive connection with the printer type execu‐
tive on a line by itself.
-t Data received on line and not recognized as printer or status
information is written to the standard output. Forces separate
read and write processes. Convenient if you have a PostScript
program that will be returning useful data to the host.
The last option is not generally recommended and should only be used if
all else fails to provide a reliable connection:
-S Slow the transmission of data to the printer. Severely limits
throughput, runs as a single process, disables the -q option,
limits the internal buffer size to 1024 bytes, can use an
excessive amount of CPU time, and does nothing in interactive
mode.
The best performance will usually be obtained by using a large internal
buffer (the -B option) and by running the program as separate read and
write processes (the -R 2 option). Inability to fork the additional
process causes postio to continue as a single read/write process. When
one process is used, only data sent to the printer is flow controlled.
The options are not all mutually exclusive. The -i option always wins,
selecting its own settings for whatever is needed to run interactive
mode, independent of anything else found on the command line. Interac‐
tive mode runs as separate read and write processes and few of the
other options accomplish anything in the presence of the -i option. The
-t option needs a reliable two way connection to the printer and
therefore tries to force separate read and write processes. The -S
option relies on the status query mechanism, so -q is disabled and the
program runs as a single process.
In most cases postio starts by making a connection to line and then
attempts to force the printer into the IDLE state by sending an appro‐
priate sequence of ^T (status query), ^C (interrupt), and ^D (end of
job) characters. When the printer goes IDLE, files are transmitted
along with an occasional ^T (unless the -q option was used). After all
the files are sent the program waits until it's reasonably sure the job
is complete. Printer generated error messages received at any time
except while establishing the initial connection (or when running
interactive mode) cause postio to exit with a non-zero status. In
addition to being added to the log file, printer error messages are
also echoed to standard error.
EXAMPLES
Example 1: Examples of the postio command.
Run as a single process at 9600 baud and send file1 and file2 to the
printer attached to /dev/tty01:
example% postio-l /dev/tty01 file1 file2
Same as above except two processes are used, the internal buffer is set
to 4096 bytes, and data returned by the printer gets put in file log:
example% postio-R 2 -B 4096 -l/dev/tty01 -L log file1 file2
Establish an interactive connection with the printer at Datakit desti‐
nation my/printer:
example% postio-i -l my/printer
Send file program to the printer connected to /dev/tty22, recover any
data in file results, and put log messages in file log:
example% postio-t -l /dev/tty22 -L log program >results
EXIT STATUS
The following exit values are returned:
0 Successful completion.
non-zero An error occurred.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
┌─────────────────────────────┬─────────────────────────────┐
│ ATTRIBUTE TYPE │ ATTRIBUTE VALUE │
├─────────────────────────────┼─────────────────────────────┤
│Availability │SUNWpsf │
└─────────────────────────────┴─────────────────────────────┘
SEE ALSOdownload(1), dpost(1), postdaisy(1), postdmd(1), postmd(1), post‐
print(1), postreverse(1), posttek(1), attributes(5)NOTES
The input files are handled as a single PostScript job. Sending several
different jobs, each with their own internal end of job mark (^D) is
not guaranteed to work properly. postio may quit before all the jobs
have completed and could be restarted before the last one finishes.
All the capabilities described above may not be available on every
machine or even across the different versions of the UNIX system that
are currently supported by the program.
There may be no default line, so using the -l option is strongly rec‐
ommended. If omitted, postio may attempt to connect to the printer
using the standard output. If Datakit is involved, the -b option may
be ineffective and attempts by postio to impose flow control over data
in both directions may not work. The -q option can help if the printer
is connected to RADIAN. The -S option is not generally recommended and
should be used only if all other attempts to establish a reliable con‐
nection fail.
SunOS 5.10 9 Sep 1996 postio(1)
