RADCLIENT(1) FreeRADIUS Daemon RADCLIENT(1)NAMEradclient - send packets to a RADIUS server, show reply
SYNOPSISradclient [-d raddb_directory] [-c count] [-f file] [-i id] [-n
num_requests_per_second] [-p num_requests_in_parallel] [-r num_retries]
[-s] [-S shared_secret_file] [-t timeout] [-qvx] server {acct|auth|sta‐
tus|disconnect} secret
DESCRIPTIONradclient is a radius client program. It can send arbitrary radius
packets to a radius server, then shows the reply. It can be used to
test changes you made in the configuration of the radius server, or it
can be used to monitor if a radius server is up.
radclient reads radius attribute/value pairs from it standard input, or
from a file specified on the command line. It then encodes these
attribute/value pairs using the dictionary, and sends them to the
remote server.
The User-Password and CHAP-Password attributes are automatically
encrypted before the packet is sent to the server.
OPTIONS-c count
Send each packet count times.
-d raddb_directory
The directory that contains the RADIUS dictionary files.
Defaults to /etc/raddb.
-f file
File to read the attribute/value pairs from. If this is not
specified, they are read from stdin. This option can be speci‐
fied multiple times, in which case packets are sent in order by
file, and within each file, by first packet to last packet. A
blank line separates logical packets within a file.
-i id Use id as the RADIUS request Id.
-n num_requests_per_second
Send num_requests_per_second, evenly spaced over time. By
default, the requests are sent as fast as possible. This option
allows you to slow down the rate at which radclient sends
requests.
-p num_requests_in_parallel
Send num_requests_in_parallel, without waiting for a response
for each one. By default, radclient sends the first request it
has read, waits for the response, and once the response is
received, sends the second request in its list. This option
allows you to send many requests at simultaneously. Once
num_requests_in_parallel are sent, radclient waits for all of
the responses to arrive (or for the requests to time out),
before sending any more packets.
-q Go to quiet mode, and do not print out anything.
-r num_retries
Try to send each packet num_retries times, before giving up on
it. The default is 10.
-s Print out some summaries of packets sent and received.
-S shared_secret_file
Rather than reading the shared secret from the command-line
(where it can be seen by others on the local system), read it
instead from shared_secret_file.
-t timeout
Wait timeout seconds before deciding that the NAS has not
responded to a request, and re-sending the packet. The default
timeout is 3.
-v Print out version information.
-x Print out debugging information.
server[:port]
The hostname or IP address of the remote server. Optionally a
UDP port can be specified. If no UDP port is specified, it is
looked up in /etc/services. The service name looked for is
radacct for accounting packets, and radius for all other
requests. If a service is not found in /etc/services, 1813 and
1812 are used respectively.
acct | auth | status | disconnect
Use auth to send an authentication packet (Access-Request), acct
to send an accounting packet (Accounting-Request), status to
send an status packet (Status-Server), or disconnect to send a
disconnection request. Instead of these values, you can also use
a decimal code here. For example, code 12 is also Status-Server.
secret The shared secret for this client. It needs to be defined on
the radius server side too, for the IP address you are sending
the radius packets from.
EXAMPLE
A sample session that queries the remote server for Status-Server (not
all servers support this, but FreeRADIUS has configurable support for
it).
$ echo "User-Name = fnord" | radclient 192.168.1.42 12 s3cr3t
Sending request to server 192.168.1.42, port 1812.
radrecv: Packet from host 192.168.1.42 code=2, id=140, length=54
Reply-Message = "FreeRADIUS up 21 days, 02:05"
SEE ALSOradiusd(8),
AUTHORS
Miquel van Smoorenburg, miquels@cistron.nl. Alan DeKok <aland@freera‐
dius.org>
7 April 2005 RADCLIENT(1)
