TCPDUMP(1)TCPDUMP(1)NAME
tcpdump - dump traffic on a network
SYNOPSIS
tcpdump [ -adeflnNOpqRStvxX ] [ -c count ] [ -F file ]
[ -i interface ] [ -m module ] [ -r file ]
[ -s snaplen ] [ -T type ] [ -w file ]
[ expression ]
DESCRIPTION
Tcpdump prints out the headers of packets on a network interface that
match the boolean expression.
Under SunOS with nit or bpf: To run tcpdump you must have read access
to /dev/nit or /dev/bpf*. Under Solaris with dlpi: You must have read
access to the network pseudo device, e.g. /dev/le. Under HP-UX with
dlpi: You must be root or it must be installed setuid to root. Under
IRIX with snoop: You must be root or it must be installed setuid to
root. Under Linux: You must be root or it must be installed setuid to
root. Under Ultrix and Digital UNIX: Once the super-user has enabled
promiscuous-mode operation using pfconfig(8), any user may run tcpdump.
Under BSD: You must have read access to /dev/bpf*.
OPTIONS-a Attempt to convert network and broadcast addresses to names.
-c Exit after receiving count packets.
-d Dump the compiled packet-matching code in a human readable form
to standard output and stop.
-dd Dump packet-matching code as a C program fragment.
-ddd Dump packet-matching code as decimal numbers (preceded with a
count).
-e Print the link-level header on each dump line.
-f Print `foreign' internet addresses numerically rather than sym‐
bolically (this option is intended to get around serious brain
damage in Sun's yp server — usually it hangs forever translating
non-local internet numbers).
-F Use file as input for the filter expression. An additional
expression given on the command line is ignored.
-i Listen on interface. If unspecified, tcpdump searches the sys‐
tem interface list for the lowest numbered, configured up inter‐
face (excluding loopback). Ties are broken by choosing the ear‐
liest match.
-l Make stdout line buffered. Useful if you want to see the data
while capturing it. E.g.,
``tcpdump -l | tee dat'' or ``tcpdump -l >
dat & tail -f dat''.
-n Don't convert addresses (i.e., host addresses, port numbers,
etc.) to names.
-N Don't print domain name qualification of host names. E.g., if
you give this flag then tcpdump will print ``nic'' instead of
``nic.ddn.mil''.
-m Load SMI MIB module definitions from file module. This option
can be used several times to load several MIB modules into tcp‐
dump.
-O Do not run the packet-matching code optimizer. This is useful
only if you suspect a bug in the optimizer.
-p Don't put the interface into promiscuous mode. Note that the
interface might be in promiscuous mode for some other reason;
hence, `-p' cannot be used as an abbreviation for `ether host
{local-hw-addr} or ether broadcast'.
-q Quick (quiet?) output. Print less protocol information so out‐
put lines are shorter.
-r Read packets from file (which was created with the -w option).
Standard input is used if file is ``-''.
-s Snarf snaplen bytes of data from each packet rather than the
default of 68 (with SunOS's NIT, the minimum is actually 96).
68 bytes is adequate for IP, ICMP, TCP and UDP but may truncate
protocol information from name server and NFS packets (see
below). Packets truncated because of a limited snapshot are
indicated in the output with ``[|proto]'', where proto is the
name of the protocol level at which the truncation has occurred.
Note that taking larger snapshots both increases the amount of
time it takes to process packets and, effectively, decreases the
amount of packet buffering. This may cause packets to be lost.
You should limit snaplen to the smallest number that will cap‐
ture the protocol information you're interested in.
-T Force packets selected by "expression" to be interpreted the
specified type. Currently known types are rpc (Remote Procedure
Call), rtp (Real-Time Applications protocol), rtcp (Real-Time
Applications control protocol), snmp (Simple Network Management
Protocol), vat (Visual Audio Tool), and wb (distributed White
Board).
-R Assume ESP/AH packets to be based on old specification (RFC1825
to RFC1829). If specified, tcpdump will not print replay pre‐
vention field. Since there is no protocol version field in
ESP/AH specification, tcpdump cannot deduce the version of
ESP/AH protocol.
-S Print absolute, rather than relative, TCP sequence numbers.
-t Don't print a timestamp on each dump line.
-tt Print an unformatted timestamp on each dump line.
-v (Slightly more) verbose output. For example, the time to live
and type of service information in an IP packet is printed.
-vv Even more verbose output. For example, additional fields are
printed from NFS reply packets.
-vvv Even more verbose output. For example, telnet SB ... SE options
are printed in full. With -X telnet options are printed in hex
as well.
-w Write the raw packets to file rather than parsing and printing
them out. They can later be printed with the -r option. Stan‐
dard output is used if file is ``-''.
-x Print each packet (minus its link level header) in hex. The
smaller of the entire packet or snaplen bytes will be printed.
-X When printing hex, print ascii too. Thus if -x is also set, the
packet is printed in hex/ascii. This is very handy for
analysing new protocols. Even if -x is not also set, some parts
of some packets may be printed in hex/ascii.
expression
selects which packets will be dumped. If no expression is
given, all packets on the net will be dumped. Otherwise, only
packets for which expression is `true' will be dumped.
The expression consists of one or more primitives. Primitives
usually consist of an id (name or number) preceded by one or
more qualifiers. There are three different kinds of qualifier:
type qualifiers say what kind of thing the id name or number
refers to. Possible types are host, net and port. E.g.,
`host foo', `net 128.3', `port 20'. If there is no type
qualifier, host is assumed.
dir qualifiers specify a particular transfer direction to
and/or from id. Possible directions are src, dst, src or
dst and src and dst. E.g., `src foo', `dst net 128.3',
`src or dst port ftp-data'. If there is no dir quali‐
fier, src or dst is assumed. For `null' link layers
(i.e. point to point protocols such as slip) the inbound
and outbound qualifiers can be used to specify a desired
direction.
proto qualifiers restrict the match to a particular protocol.
Possible protos are: ether, fddi, ip, ip6, arp, rarp,
decnet, lat, sca, moprc, mopdl, icmp, icmp6, tcp and udp.
E.g., `ether src foo', `arp net 128.3', `tcp port 21'.
If there is no proto qualifier, all protocols consistent
with the type are assumed. E.g., `src foo' means `(ip or
arp or rarp) src foo' (except the latter is not legal
syntax), `net bar' means `(ip or arp or rarp) net bar'
and `port 53' means `(tcp or udp) port 53'.
[`fddi' is actually an alias for `ether'; the parser treats them
identically as meaning ``the data link level used on the speci‐
fied network interface.'' FDDI headers contain Ethernet-like
source and destination addresses, and often contain Ethernet-
like packet types, so you can filter on these FDDI fields just
as with the analogous Ethernet fields. FDDI headers also con‐
tain other fields, but you cannot name them explicitly in a fil‐
ter expression.]
In addition to the above, there are some special `primitive'
keywords that don't follow the pattern: gateway, broadcast,
less, greater and arithmetic expressions. All of these are
described below.
More complex filter expressions are built up by using the words
and, or and not to combine primitives. E.g., `host foo and not
port ftp and not port ftp-data'. To save typing, identical
qualifier lists can be omitted. E.g., `tcp dst port ftp or ftp-
data or domain' is exactly the same as `tcp dst port ftp or tcp
dst port ftp-data or tcp dst port domain'.
Allowable primitives are:
dst host host
True if the IPv4/v6 destination field of the packet is
host, which may be either an address or a name.
src host host
True if the IPv4/v6 source field of the packet is host.
host host
True if either the IPv4/v6 source or destination of the
packet is host. Any of the above host expressions can be
prepended with the keywords, ip, arp, rarp, or ip6 as in:
ip host host
which is equivalent to:
ether proto \ip and host host
If host is a name with multiple IP addresses, each
address will be checked for a match.
ether dst ehost
True if the ethernet destination address is ehost. Ehost
may be either a name from /etc/ethers or a number (see
ethers(3N) for numeric format).
ether src ehost
True if the ethernet source address is ehost.
ether host ehost
True if either the ethernet source or destination address
is ehost.
gateway host
True if the packet used host as a gateway. I.e., the
ethernet source or destination address was host but nei‐
ther the IP source nor the IP destination was host. Host
must be a name and must be found in both /etc/hosts and
/etc/ethers. (An equivalent expression is
ether host ehost and not host host
which can be used with either names or numbers for host /
ehost.) This syntax does not work in IPv6-enabled con‐
figuration at this moment.
dst net net
True if the IPv4/v6 destination address of the packet has
a network number of net. Net may be either a name from
/etc/networks or a network number (see networks(4) for
details).
src net net
True if the IPv4/v6 source address of the packet has a
network number of net.
net net
True if either the IPv4/v6 source or destination address
of the packet has a network number of net.
net net mask mask
True if the IP address matches net with the specific net‐
mask. May be qualified with src or dst. Note that this
syntax is not valid for IPv6 net.
net net/len
True if the IPv4/v6 address matches net a netmask len
bits wide. May be qualified with src or dst.
dst port port
True if the packet is ip/tcp, ip/udp, ip6/tcp or ip6/udp
and has a destination port value of port. The port can
be a number or a name used in /etc/services (see tcp(4P)
and udp(4P)). If a name is used, both the port number
and protocol are checked. If a number or ambiguous name
is used, only the port number is checked (e.g., dst port
513 will print both tcp/login traffic and udp/who traf‐
fic, and port domain will print both tcp/domain and
udp/domain traffic).
src port port
True if the packet has a source port value of port.
port port
True if either the source or destination port of the
packet is port. Any of the above port expressions can be
prepended with the keywords, tcp or udp, as in:
tcp src port port
which matches only tcp packets whose source port is port.
less length
True if the packet has a length less than or equal to
length. This is equivalent to:
len <= length.
greater length
True if the packet has a length greater than or equal to
length. This is equivalent to:
len >= length.
ip proto protocol
True if the packet is an ip packet (see ip(4P)) of proto‐
col type protocol. Protocol can be a number or one of
the names icmp, igrp, udp, nd, or tcp. Note that the
identifiers tcp, udp, and icmp are also keywords and must
be escaped via backslash (\), which is \\ in the C-shell.
Note that this primitive does not chase protocol header
chain.
ip6 proto protocol
True if the packet is an IPv6 packet of protocol type
protocol. Note that this primitive does not chase proto‐
col header chain.
ip6 protochain protocol
True if the packet is IPv6 packet, and contains protocol
header with type protocol in its protocol header chain.
For example,
ip6 protochain 6
matches any IPv6 packet with TCP protocol header in the
protocol header chain. The packet may contain, for exam‐
ple, authentication header, routing header, or hop-by-hop
option header, between IPv6 header and TCP header. The
BPF code emitted by this primitive is complex and cannot
be optimized by BPF optimizer code in tcpdump, so this
can be somewhat slow.
ip protochain protocol
Equivalent to ip6 protochain protocol, but this is for
IPv4.
ether broadcast
True if the packet is an ethernet broadcast packet. The
ether keyword is optional.
ip broadcast
True if the packet is an IP broadcast packet. It checks
for both the all-zeroes and all-ones broadcast conven‐
tions, and looks up the local subnet mask.
ether multicast
True if the packet is an ethernet multicast packet. The
ether keyword is optional. This is shorthand for
`ether[0] & 1 != 0'.
ip multicast
True if the packet is an IP multicast packet.
ip6 multicast
True if the packet is an IPv6 multicast packet.
ether proto protocol
True if the packet is of ether type protocol. Protocol
can be a number or a name like ip, ip6, arp, or rarp.
Note these identifiers are also keywords and must be
escaped via backslash (\). [In the case of FDDI (e.g.,
`fddi protocol arp'), the protocol identification comes
from the 802.2 Logical Link Control (LLC) header, which
is usually layered on top of the FDDI header. Tcpdump
assumes, when filtering on the protocol identifier, that
all FDDI packets include an LLC header, and that the LLC
header is in so-called SNAP format.]
decnet src host
True if the DECNET source address is host, which may be
an address of the form ``10.123'', or a DECNET host name.
[DECNET host name support is only available on Ultrix
systems that are configured to run DECNET.]
decnet dst host
True if the DECNET destination address is host.
decnet host host
True if either the DECNET source or destination address
is host.
ip, ip6, arp, rarp, decnet
Abbreviations for:
ether proto p
where p is one of the above protocols.
lat, moprc, mopdl
Abbreviations for:
ether proto p
where p is one of the above protocols. Note that tcpdump
does not currently know how to parse these protocols.
tcp, udp, icmp
Abbreviations for:
ip proto p or ip6 proto p
where p is one of the above protocols.
expr relop expr
True if the relation holds, where relop is one of >, <,
>=, <=, =, !=, and expr is an arithmetic expression com‐
posed of integer constants (expressed in standard C syn‐
tax), the normal binary operators [+, -, *, /, &, |], a
length operator, and special packet data accessors. To
access data inside the packet, use the following syntax:
proto [ expr : size ]
Proto is one of ether, fddi, ip, arp, rarp, tcp, udp,
icmp or ip6, and indicates the protocol layer for the
index operation. Note that tcp, udp and other upper-
layer protocol types only apply to IPv4, not IPv6 (this
will be fixed in the future). The byte offset, relative
to the indicated protocol layer, is given by expr. Size
is optional and indicates the number of bytes in the
field of interest; it can be either one, two, or four,
and defaults to one. The length operator, indicated by
the keyword len, gives the length of the packet.
For example, `ether[0] & 1 != 0' catches all multicast
traffic. The expression `ip[0] & 0xf != 5' catches all
IP packets with options. The expression `ip[6:2] & 0x1fff
= 0' catches only unfragmented datagrams and frag zero of
fragmented datagrams. This check is implicitly applied
to the tcp and udp index operations. For instance,
tcp[0] always means the first byte of the TCP header, and
never means the first byte of an intervening fragment.
Primitives may be combined using:
A parenthesized group of primitives and operators (paren‐
theses are special to the Shell and must be escaped).
Negation (`!' or `not').
Concatenation (`&&' or `and').
Alternation (`||' or `or').
Negation has highest precedence. Alternation and concatenation
have equal precedence and associate left to right. Note that
explicit and tokens, not juxtaposition, are now required for
concatenation.
If an identifier is given without a keyword, the most recent
keyword is assumed. For example,
not host vs and ace
is short for
not host vs and host ace
which should not be confused with
not ( host vs or ace )
Expression arguments can be passed to tcpdump as either a single
argument or as multiple arguments, whichever is more convenient.
Generally, if the expression contains Shell metacharacters, it
is easier to pass it as a single, quoted argument. Multiple
arguments are concatenated with spaces before being parsed.
EXAMPLES
To print all packets arriving at or departing from sundown:
tcpdump host sundown
To print traffic between helios and either hot or ace:
tcpdump host helios and \( hot or ace \)
To print all IP packets between ace and any host except helios:
tcpdump ip host ace and not helios
To print all traffic between local hosts and hosts at Berkeley:
tcpdump net ucb-ether
To print all ftp traffic through internet gateway snup: (note that the
expression is quoted to prevent the shell from (mis-)interpreting the
parentheses):
tcpdump 'gateway snup and (port ftp or ftp-data)'
To print traffic neither sourced from nor destined for local hosts (if
you gateway to one other net, this stuff should never make it onto your
local net).
tcpdump ip and not net localnet
To print the start and end packets (the SYN and FIN packets) of each
TCP conversation that involves a non-local host.
tcpdump 'tcp[13] & 3 != 0 and not src and dst net localnet'
To print IP packets longer than 576 bytes sent through gateway snup:
tcpdump 'gateway snup and ip[2:2] > 576'
To print IP broadcast or multicast packets that were not sent via eth‐
ernet broadcast or multicast:
tcpdump 'ether[0] & 1 = 0 and ip[16] >= 224'
To print all ICMP packets that are not echo requests/replies (i.e., not
ping packets):
tcpdump 'icmp[0] != 8 and icmp[0] != 0"
OUTPUT FORMAT
The output of tcpdump is protocol dependent. The following gives a
brief description and examples of most of the formats.
Link Level Headers
If the '-e' option is given, the link level header is printed out. On
ethernets, the source and destination addresses, protocol, and packet
length are printed.
On FDDI networks, the '-e' option causes tcpdump to print the `frame
control' field, the source and destination addresses, and the packet
length. (The `frame control' field governs the interpretation of the
rest of the packet. Normal packets (such as those containing IP data‐
grams) are `async' packets, with a priority value between 0 and 7; for
example, `async4'. Such packets are assumed to contain an 802.2 Logi‐
cal Link Control (LLC) packet; the LLC header is printed if it is not
an ISO datagram or a so-called SNAP packet.
(N.B.: The following description assumes familiarity with the SLIP com‐
pression algorithm described in RFC-1144.)
On SLIP links, a direction indicator (``I'' for inbound, ``O'' for out‐
bound), packet type, and compression information are printed out. The
packet type is printed first. The three types are ip, utcp, and ctcp.
No further link information is printed for ip packets. For TCP pack‐
ets, the connection identifier is printed following the type. If the
packet is compressed, its encoded header is printed out. The special
cases are printed out as *S+n and *SA+n, where n is the amount by which
the sequence number (or sequence number and ack) has changed. If it is
not a special case, zero or more changes are printed. A change is
indicated by U (urgent pointer), W (window), A (ack), S (sequence num‐
ber), and I (packet ID), followed by a delta (+n or -n), or a new value
(=n). Finally, the amount of data in the packet and compressed header
length are printed.
For example, the following line shows an outbound compressed TCP
packet, with an implicit connection identifier; the ack has changed by
6, the sequence number by 49, and the packet ID by 6; there are 3 bytes
of data and 6 bytes of compressed header:
O ctcp * A+6 S+49 I+6 3 (6)
ARP/RARP Packets
Arp/rarp output shows the type of request and its arguments. The for‐
mat is intended to be self explanatory. Here is a short sample taken
from the start of an `rlogin' from host rtsg to host csam:
arp who-has csam tell rtsg
arp reply csam is-at CSAM
The first line says that rtsg sent an arp packet asking for the ether‐
net address of internet host csam. Csam replies with its ethernet
address (in this example, ethernet addresses are in caps and internet
addresses in lower case).
This would look less redundant if we had done tcpdump -n:
arp who-has 128.3.254.6 tell 128.3.254.68
arp reply 128.3.254.6 is-at 02:07:01:00:01:c4
If we had done tcpdump -e, the fact that the first packet is broadcast
and the second is point-to-point would be visible:
RTSG Broadcast 0806 64: arp who-has csam tell rtsg
CSAM RTSG 0806 64: arp reply csam is-at CSAM
For the first packet this says the ethernet source address is RTSG, the
destination is the ethernet broadcast address, the type field contained
hex 0806 (type ETHER_ARP) and the total length was 64 bytes.
TCP Packets
(N.B.:The following description assumes familiarity with the TCP proto‐
col described in RFC-793. If you are not familiar with the protocol,
neither this description nor tcpdump will be of much use to you.)
The general format of a tcp protocol line is:
src > dst: flags data-seqno ack window urgent options
Src and dst are the source and destination IP addresses and ports.
Flags are some combination of S (SYN), F (FIN), P (PUSH) or R (RST) or
a single `.' (no flags). Data-seqno describes the portion of sequence
space covered by the data in this packet (see example below). Ack is
sequence number of the next data expected the other direction on this
connection. Window is the number of bytes of receive buffer space
available the other direction on this connection. Urg indicates there
is `urgent' data in the packet. Options are tcp options enclosed in
angle brackets (e.g., <mss 1024>).
Src, dst and flags are always present. The other fields depend on the
contents of the packet's tcp protocol header and are output only if
appropriate.
Here is the opening portion of an rlogin from host rtsg to host csam.
rtsg.1023 > csam.login: S 768512:768512(0) win 4096 <mss 1024>
csam.login > rtsg.1023: S 947648:947648(0) ack 768513 win 4096 <mss 1024>
rtsg.1023 > csam.login: . ack 1 win 4096
rtsg.1023 > csam.login: P 1:2(1) ack 1 win 4096
csam.login > rtsg.1023: . ack 2 win 4096
rtsg.1023 > csam.login: P 2:21(19) ack 1 win 4096
csam.login > rtsg.1023: P 1:2(1) ack 21 win 4077
csam.login > rtsg.1023: P 2:3(1) ack 21 win 4077 urg 1
csam.login > rtsg.1023: P 3:4(1) ack 21 win 4077 urg 1
The first line says that tcp port 1023 on rtsg sent a packet to port
login on csam. The S indicates that the SYN flag was set. The packet
sequence number was 768512 and it contained no data. (The notation is
`first:last(nbytes)' which means `sequence numbers first up to but not
including last which is nbytes bytes of user data'.) There was no
piggy-backed ack, the available receive window was 4096 bytes and there
was a max-segment-size option requesting an mss of 1024 bytes.
Csam replies with a similar packet except it includes a piggy-backed
ack for rtsg's SYN. Rtsg then acks csam's SYN. The `.' means no flags
were set. The packet contained no data so there is no data sequence
number. Note that the ack sequence number is a small integer (1). The
first time tcpdump sees a tcp `conversation', it prints the sequence
number from the packet. On subsequent packets of the conversation, the
difference between the current packet's sequence number and this ini‐
tial sequence number is printed. This means that sequence numbers
after the first can be interpreted as relative byte positions in the
conversation's data stream (with the first data byte each direction
being `1'). `-S' will override this feature, causing the original
sequence numbers to be output.
On the 6th line, rtsg sends csam 19 bytes of data (bytes 2 through 20
in the rtsg → csam side of the conversation). The PUSH flag is set in
the packet. On the 7th line, csam says it's received data sent by rtsg
up to but not including byte 21. Most of this data is apparently sit‐
ting in the socket buffer since csam's receive window has gotten 19
bytes smaller. Csam also sends one byte of data to rtsg in this
packet. On the 8th and 9th lines, csam sends two bytes of urgent,
pushed data to rtsg.
If the snapshot was small enough that tcpdump didn't capture the full
TCP header, it interprets as much of the header as it can and then
reports ``[|tcp]'' to indicate the remainder could not be interpreted.
If the header contains a bogus option (one with a length that's either
too small or beyond the end of the header), tcpdump reports it as
``[bad opt]'' and does not interpret any further options (since it's
impossible to tell where they start). If the header length indicates
options are present but the IP datagram length is not long enough for
the options to actually be there, tcpdump reports it as ``[bad hdr
length]''.
UDP Packets
UDP format is illustrated by this rwho packet:
actinide.who > broadcast.who: udp 84
This says that port who on host actinide sent a udp datagram to port
who on host broadcast, the Internet broadcast address. The packet con‐
tained 84 bytes of user data.
Some UDP services are recognized (from the source or destination port
number) and the higher level protocol information printed. In particu‐
lar, Domain Name service requests (RFC-1034/1035) and Sun RPC calls
(RFC-1050) to NFS.
UDP Name Server Requests
(N.B.:The following description assumes familiarity with the Domain
Service protocol described in RFC-1035. If you are not familiar with
the protocol, the following description will appear to be written in
greek.)
Name server requests are formatted as
src > dst: id op? flags qtype qclass name (len)
h2opolo.1538 > helios.domain: 3+ A? ucbvax.berkeley.edu. (37)
Host h2opolo asked the domain server on helios for an address record
(qtype=A) associated with the name ucbvax.berkeley.edu. The query id
was `3'. The `+' indicates the recursion desired flag was set. The
query length was 37 bytes, not including the UDP and IP protocol head‐
ers. The query operation was the normal one, Query, so the op field
was omitted. If the op had been anything else, it would have been
printed between the `3' and the `+'. Similarly, the qclass was the
normal one, C_IN, and omitted. Any other qclass would have been
printed immediately after the `A'.
A few anomalies are checked and may result in extra fields enclosed in
square brackets: If a query contains an answer, name server or author‐
ity section, ancount, nscount, or arcount are printed as `[na]', `[nn]'
or `[nau]' where n is the appropriate count. If any of the response
bits are set (AA, RA or rcode) or any of the `must be zero' bits are
set in bytes two and three, `[b2&3=x]' is printed, where x is the hex
value of header bytes two and three.
UDP Name Server Responses
Name server responses are formatted as
src > dst: id op rcode flags a/n/au type class data (len)
helios.domain > h2opolo.1538: 3 3/3/7 A 128.32.137.3 (273)
helios.domain > h2opolo.1537: 2 NXDomain* 0/1/0 (97)
In the first example, helios responds to query id 3 from h2opolo with 3
answer records, 3 name server records and 7 authority records. The
first answer record is type A (address) and its data is internet
address 128.32.137.3. The total size of the response was 273 bytes,
excluding UDP and IP headers. The op (Query) and response code (NoEr‐
ror) were omitted, as was the class (C_IN) of the A record.
In the second example, helios responds to query 2 with a response code
of non-existent domain (NXDomain) with no answers, one name server and
no authority records. The `*' indicates that the authoritative answer
bit was set. Since there were no answers, no type, class or data were
printed.
Other flag characters that might appear are `-' (recursion available,
RA, not set) and `|' (truncated message, TC, set). If the `question'
section doesn't contain exactly one entry, `[nq]' is printed.
Note that name server requests and responses tend to be large and the
default snaplen of 68 bytes may not capture enough of the packet to
print. Use the -s flag to increase the snaplen if you need to seri‐
ously investigate name server traffic. `-s 128' has worked well for
me.
SMB/CIFS decoding
tcpdump now includes fairly extensive SMB/CIFS/NBT decoding for data on
UDP/137, UDP/138 and TCP/139. Some primitive decoding of IPX and Net‐
BEUI SMB data is also done.
By default a fairly minimal decode is done, with a much more detailed
decode done if -v is used. Be warned that with -v a single SMB packet
may take up a page or more, so only use -v if you really want all the
gory details.
If you are decoding SMB sessions containing unicode strings then you
may wish to set the environment variable USE_UNICODE to 1. A patch to
auto-detect unicode srings would be welcome.
For information on SMB packet formats and what all te fields mean see
www.cifs.org or the pub/samba/specs/ directory on your favourite
samba.org mirror site. The SMB patches were written by Andrew Tridgell
(tridge@samba.org).
NFS Requests and Replies
Sun NFS (Network File System) requests and replies are printed as:
src.xid > dst.nfs: len op args
src.nfs > dst.xid: reply stat len op results
sushi.6709 > wrl.nfs: 112 readlink fh 21,24/10.73165
wrl.nfs > sushi.6709: reply ok 40 readlink "../var"
sushi.201b > wrl.nfs:
144 lookup fh 9,74/4096.6878 "xcolors"
wrl.nfs > sushi.201b:
reply ok 128 lookup fh 9,74/4134.3150
In the first line, host sushi sends a transaction with id 6709 to wrl
(note that the number following the src host is a transaction id, not
the source port). The request was 112 bytes, excluding the UDP and IP
headers. The operation was a readlink (read symbolic link) on file
handle (fh) 21,24/10.731657119. (If one is lucky, as in this case, the
file handle can be interpreted as a major,minor device number pair,
followed by the inode number and generation number.) Wrl replies `ok'
with the contents of the link.
In the third line, sushi asks wrl to lookup the name `xcolors' in
directory file 9,74/4096.6878. Note that the data printed depends on
the operation type. The format is intended to be self explanatory if
read in conjunction with an NFS protocol spec.
If the -v (verbose) flag is given, additional information is printed.
For example:
sushi.1372a > wrl.nfs:
148 read fh 21,11/12.195 8192 bytes @ 24576
wrl.nfs > sushi.1372a:
reply ok 1472 read REG 100664 ids 417/0 sz 29388
(-v also prints the IP header TTL, ID, and fragmentation fields, which
have been omitted from this example.) In the first line, sushi asks
wrl to read 8192 bytes from file 21,11/12.195, at byte offset 24576.
Wrl replies `ok'; the packet shown on the second line is the first
fragment of the reply, and hence is only 1472 bytes long (the other
bytes will follow in subsequent fragments, but these fragments do not
have NFS or even UDP headers and so might not be printed, depending on
the filter expression used). Because the -v flag is given, some of the
file attributes (which are returned in addition to the file data) are
printed: the file type (``REG'', for regular file), the file mode (in
octal), the uid and gid, and the file size.
If the -v flag is given more than once, even more details are printed.
Note that NFS requests are very large and much of the detail won't be
printed unless snaplen is increased. Try using `-s 192' to watch NFS
traffic.
NFS reply packets do not explicitly identify the RPC operation.
Instead, tcpdump keeps track of ``recent'' requests, and matches them
to the replies using the transaction ID. If a reply does not closely
follow the corresponding request, it might not be parsable.
AFS Requests and Replies
Transarc AFS (Andrew File System) requests and replies are printed as:
src.sport > dst.dport: rx packet-type
src.sport > dst.dport: rx packet-type service call call-name args
src.sport > dst.dport: rx packet-type service reply call-name args
elvis.7001 > pike.afsfs:
rx data fs call rename old fid 536876964/1/1 ".newsrc.new"
new fid 536876964/1/1 ".newsrc"
pike.afsfs > elvis.7001: rx data fs reply rename
In the first line, host elvis sends a RX packet to pike. This was a RX
data packet to the fs (fileserver) service, and is the start of an RPC
call. The RPC call was a rename, with the old directory file id of
536876964/1/1 and an old filename of `.newsrc.new', and a new directory
file id of 536876964/1/1 and a new filename of `.newsrc'. The host
pike responds with a RPC reply to the rename call (which was success‐
ful, because it was a data packet and not an abort packet).
In general, all AFS RPCs are decoded at least by RPC call name. Most
AFS RPCs have at least some of the arguments decoded (generally only
the `interesting' arguments, for some definition of interesting).
The format is intended to be self-describing, but it will probably not
be useful to people who are not familiar with the workings of AFS and
RX.
If the -v (verbose) flag is given twice, additional information is
printed, such as the the RX call ID, call number, sequence number,
serial number, and the RX packet flags.
If the -v flag is given again, the security index and service id are
printed.
Error codes are printed for abort packets, with the exception of Ubik
beacon packets (because abort packets are used to signify a yes vote
for the Ubik protocol).
Note that AFS requests are very large and many of the arguments won't
be printed unless snaplen is increased. Try using `-s 256' to watch
AFS traffic.
AFS reply packets do not explicitly identify the RPC operation.
Instead, tcpdump keeps track of ``recent'' requests, and matches them
to the replies using the call number and service ID. If a reply does
not closely follow the corresponding request, it might not be parsable.
KIP Appletalk (DDP in UDP)
Appletalk DDP packets encapsulated in UDP datagrams are de-encapsulated
and dumped as DDP packets (i.e., all the UDP header information is dis‐
carded). The file /etc/atalk.names is used to translate appletalk net
and node numbers to names. Lines in this file have the form
number name
1.254 ether
16.1 icsd-net
1.254.110 ace
The first two lines give the names of appletalk networks. The third
line gives the name of a particular host (a host is distinguished from
a net by the 3rd octet in the number - a net number must have two
octets and a host number must have three octets.) The number and name
should be separated by whitespace (blanks or tabs). The
/etc/atalk.names file may contain blank lines or comment lines (lines
starting with a `#').
Appletalk addresses are printed in the form
net.host.port
144.1.209.2 > icsd-net.112.220
office.2 > icsd-net.112.220
jssmag.149.235 > icsd-net.2
(If the /etc/atalk.names doesn't exist or doesn't contain an entry for
some appletalk host/net number, addresses are printed in numeric form.)
In the first example, NBP (DDP port 2) on net 144.1 node 209 is sending
to whatever is listening on port 220 of net icsd node 112. The second
line is the same except the full name of the source node is known
(`office'). The third line is a send from port 235 on net jssmag node
149 to broadcast on the icsd-net NBP port (note that the broadcast
address (255) is indicated by a net name with no host number - for this
reason it's a good idea to keep node names and net names distinct in
/etc/atalk.names).
NBP (name binding protocol) and ATP (Appletalk transaction protocol)
packets have their contents interpreted. Other protocols just dump the
protocol name (or number if no name is registered for the protocol) and
packet size.
NBP packets are formatted like the following examples:
icsd-net.112.220 > jssmag.2: nbp-lkup 190: "=:LaserWriter@*"
jssmag.209.2 > icsd-net.112.220: nbp-reply 190: "RM1140:LaserWriter@*" 250
techpit.2 > icsd-net.112.220: nbp-reply 190: "techpit:LaserWriter@*" 186
The first line is a name lookup request for laserwriters sent by net
icsd host 112 and broadcast on net jssmag. The nbp id for the lookup
is 190. The second line shows a reply for this request (note that it
has the same id) from host jssmag.209 saying that it has a laserwriter
resource named "RM1140" registered on port 250. The third line is
another reply to the same request saying host techpit has laserwriter
"techpit" registered on port 186.
ATP packet formatting is demonstrated by the following example:
jssmag.209.165 > helios.132: atp-req 12266<0-7> 0xae030001
helios.132 > jssmag.209.165: atp-resp 12266:0 (512) 0xae040000
helios.132 > jssmag.209.165: atp-resp 12266:1 (512) 0xae040000
helios.132 > jssmag.209.165: atp-resp 12266:2 (512) 0xae040000
helios.132 > jssmag.209.165: atp-resp 12266:3 (512) 0xae040000
helios.132 > jssmag.209.165: atp-resp 12266:4 (512) 0xae040000
helios.132 > jssmag.209.165: atp-resp 12266:5 (512) 0xae040000
helios.132 > jssmag.209.165: atp-resp 12266:6 (512) 0xae040000
helios.132 > jssmag.209.165: atp-resp*12266:7 (512) 0xae040000
jssmag.209.165 > helios.132: atp-req 12266<3,5> 0xae030001
helios.132 > jssmag.209.165: atp-resp 12266:3 (512) 0xae040000
helios.132 > jssmag.209.165: atp-resp 12266:5 (512) 0xae040000
jssmag.209.165 > helios.132: atp-rel 12266<0-7> 0xae030001
jssmag.209.133 > helios.132: atp-req* 12267<0-7> 0xae030002
Jssmag.209 initiates transaction id 12266 with host helios by request‐
ing up to 8 packets (the `<0-7>'). The hex number at the end of the
line is the value of the `userdata' field in the request.
Helios responds with 8 512-byte packets. The `:digit' following the
transaction id gives the packet sequence number in the transaction and
the number in parens is the amount of data in the packet, excluding the
atp header. The `*' on packet 7 indicates that the EOM bit was set.
Jssmag.209 then requests that packets 3 & 5 be retransmitted. Helios
resends them then jssmag.209 releases the transaction. Finally, jss‐
mag.209 initiates the next request. The `*' on the request indicates
that XO (`exactly once') was not set.
IP Fragmentation
Fragmented Internet datagrams are printed as
(frag id:size@offset+)
(frag id:size@offset)
(The first form indicates there are more fragments. The second indi‐
cates this is the last fragment.)
Id is the fragment id. Size is the fragment size (in bytes) excluding
the IP header. Offset is this fragment's offset (in bytes) in the
original datagram.
The fragment information is output for each fragment. The first frag‐
ment contains the higher level protocol header and the frag info is
printed after the protocol info. Fragments after the first contain no
higher level protocol header and the frag info is printed after the
source and destination addresses. For example, here is part of an ftp
from arizona.edu to lbl-rtsg.arpa over a CSNET connection that doesn't
appear to handle 576 byte datagrams:
arizona.ftp-data > rtsg.1170: . 1024:1332(308) ack 1 win 4096 (frag 595a:328@0+)
arizona > rtsg: (frag 595a:204@328)
rtsg.1170 > arizona.ftp-data: . ack 1536 win 2560
There are a couple of things to note here: First, addresses in the 2nd
line don't include port numbers. This is because the TCP protocol
information is all in the first fragment and we have no idea what the
port or sequence numbers are when we print the later fragments. Sec‐
ond, the tcp sequence information in the first line is printed as if
there were 308 bytes of user data when, in fact, there are 512 bytes
(308 in the first frag and 204 in the second). If you are looking for
holes in the sequence space or trying to match up acks with packets,
this can fool you.
A packet with the IP don't fragment flag is marked with a trailing
(DF).
Timestamps
By default, all output lines are preceded by a timestamp. The time‐
stamp is the current clock time in the form
hh:mm:ss.frac
and is as accurate as the kernel's clock. The timestamp reflects the
time the kernel first saw the packet. No attempt is made to account
for the time lag between when the ethernet interface removed the packet
from the wire and when the kernel serviced the `new packet' interrupt.
SEE ALSOtraffic(1C), nit(4P), bpf(4), pcap(3)AUTHORS
The original authors are:
Van Jacobson, Craig Leres and Steven McCanne, all of the Lawrence
Berkeley National Laboratory, University of California, Berkeley, CA.
It is currently being maintained by tcpdump.org.
http://www.tcpdump.org/
IPv6/IPsec support is added by WIDE/KAME project. This program uses
Eric Young's SSLeay library, under specific configuration.
BUGS
Please send problems, bugs, questions, desirable enhancements, etc. to:
tcpdump-workers@tcpdump.org
Please send source code contributions, etc. to:
patches@tcpdump.org
NIT doesn't let you watch your own outbound traffic, BPF will. We rec‐
ommend that you use the latter.
Some attempt should be made to reassemble IP fragments or, at least to
compute the right length for the higher level protocol.
Name server inverse queries are not dumped correctly: The (empty) ques‐
tion section is printed rather than real query in the answer section.
Some believe that inverse queries are themselves a bug and prefer to
fix the program generating them rather than tcpdump.
Apple Ethertalk DDP packets could be dumped as easily as KIP DDP pack‐
ets but aren't. Even if we were inclined to do anything to promote the
use of Ethertalk (we aren't), LBL doesn't allow Ethertalk on any of its
networks so we'd would have no way of testing this code.
A packet trace that crosses a daylight savings time change will give
skewed time stamps (the time change is ignored).
Filters expressions that manipulate FDDI headers assume that all FDDI
packets are encapsulated Ethernet packets. This is true for IP, ARP,
and DECNET Phase IV, but is not true for protocols such as ISO CLNS.
Therefore, the filter may inadvertently accept certain packets that do
not properly match the filter expression.
ip6 proto should chase header chain, but at this moment it does not.
tcp or udp should chase header chain too.
Arithmetic expression against transport layer headers, like tcp[0],
does not work against IPv6 packets. It only looks at IPv4 packets.
30 June 1997 TCPDUMP(1)