snmpnetstat(1M) System Administration Commands snmpnetstat(1M)NAMEsnmpnetstat - show network status using SNMP
SYNOPSIS
/usr/sfw/bin/snmpnetstat [common options] [-a] [-n] agent
/usr/sfw/sma_snmp/bin/snmpnetstat [common options] [-iorns] agent
/usr/sfw/sma_snmp/bin/snmpnetstat [common options] [-in] [-I interface]
agent [interval]
/usr/sfw/sma_snmp/bin/snmpnetstat [common options] [-an] [-s] [-P pro‐
tocol] agent
DESCRIPTION
The snmpnetstat command symbolically displays the values of various
network-related information retrieved from a remote system using the
SNMP protocol. There are a number of output formats, depending on the
options for the information presented. Referring to the SYNOPSIS,
above:
· The first form of the command displays a list of active sockets.
· The second form presents the values of other network-related
information according to the option selected.
· The third form, with an interval specified, continuously displays
the information regarding packet traffic on the configured network
interfaces.
· The fourth form displays statistics about the named protocol.
The operand agent identifies a target SNMP agent that is instrumented
to monitor the given objects. At its simplest, the agent specification
consists of a host name or an IPv4 address. In this situation, the com‐
mand attempts communication with the agent using UDP/IPv4 to port 161
of the target host. See snmpcmd(1M) for a full list of the possible
formats for agent.
The version 1 and version 2c community specifies the community name for
the transaction with the remote system.
OPTIONS
The following options are supported:
common options
See snmpcmd(1M) for a list of possible values for common options,
as well as their descriptions.
-a
With the default display, show the state of all sockets. Normally,
sockets used by server processes are not shown.
-i
Show the state of all of the network interfaces. The interface dis‐
play provides a table of cumulative statistics regarding packets
transferred, errors, and collisions. The network addresses of the
interface and the maximum transmission unit (MTU) are also dis‐
played.
-o
Show an abbreviated interface status, giving octets in place of
packets. This is useful when observing virtual interfaces (such as
Frame Relay circuits) on a router.
-I interface
Show information only about this interface; used with an interval
as described below.
-n
Show network addresses as numbers. (Normally, snmpnetstat inter‐
prets addresses and attempts to display them symbolically). This
option can be used with any of the display formats.
-P protocol
Show statistics about protocol, which is either a well-known name
for a protocol or an alias for it. Some protocol names and aliases
are listed in the file /etc/protocols or in a naming service. A
null response typically means that there are no interesting numbers
to report. The program will complain if protocol is unknown or if
there is no statistics routine for it.
-s
Show per-protocol statistics. When used with the -r option, show
routing statistics instead.
-r
Show the routing tables. When -s is also present, show per-protocol
routing statistics instead of the routing tables.
interval
When snmpnetstat is invoked with an interval argument, it displays
a running count of statistics related to network interfaces. inter‐
val is the number of seconds between reporting of statistics.
snmpnetstat supports the following types of display:
active sockets display (default)
The default display, for active sockets, shows the local and remote
addresses, protocol, and the internal state of the protocol.
Address formats are of the form host.port or network.port if a
socket's address specifies a network but no specific host address.
When known, the host and network addresses are displayed symboli‐
cally according to /etc/hosts and /etc/networks, respectively. If a
symbolic name for an address is unknown, or if the -n option is
specified, the address is printed numerically, according to the
address family. For more information regarding the Internet "dot
format," refer to inet(3SOCKET). Unspecified, or wildcard,
addresses and ports appear as "∗".
interface display
The interface display provides a table of cumulative statistics
regarding packets transferred, errors, and collisions. The network
addresses of the interface and the maximum transmission unit (MTU)
are also displayed.
routing table display
The routing table display indicates the available routes and their
status. Each route consists of a destination host or network and a
gateway to use in forwarding packets. The flags field shows the
state of the route (U if the route is up), whether the route is to
a gateway (G), whether the route was created dynamically by a redi‐
rect (D), and whether the route has been modified by a redirect
(M). Direct routes are created for each interface attached to the
local host. The gateway field for such entries shows the address of
the outgoing interface. The interface entry indicates the network
interface used for the route.
interface display with an interval
When snmpnetstat is invoked with an interval argument, it displays
a running count of statistics related to network interfaces. This
display consists of a column for the primary interface and a column
summarizing information for all interfaces. The primary interface
can be replaced with another interface with the -I option. The
first line of each screen of information contains a summary since
the system was last rebooted. Subsequent lines of output show val‐
ues accumulated over the preceding interval.
active sockets display for a single protocol
When a protocol is specified with the -P option, the information
displayed is similar to that in the default display for active
sockets, except the display is limited to the given protocol.
Note that figures snmpnetstat reports in the Ipkts column (part of the
interface display) might differ from figures in the Ipkts column in
netstat(1M). snmpnetstat displays a total of unicast, multicast, and
broadcast packets. netstat omits broadcast packets from its total.
EXAMPLES
Example 1: Displaying Active Sockets
The following is an example of snmpnetstat's default display, which is
to display active sockets.
% snmpnetstat-v 2c -c public -a testhost
Active Internet (tcp) Connections (including servers)
Proto Local Address Foreign Address (state)
tcp *.echo *.* LISTEN
tcp *.discard *.* LISTEN
tcp *.daytime *.* LISTEN
tcp *.chargen *.* LISTEN
tcp *.ftp *.* LISTEN
tcp *.telnet *.* LISTEN
tcp *.smtp *.* LISTEN
Active Internet (udp) Connections
Proto Local Address
udp *.echo
udp *.discard
udp *.daytime
udp *.chargen
udp *.time
% snmpnetstat-v 2c -c public -i testhost
Name Mtu Network Address Ipkts Ierrs Opkts Oerrs Queue
eri0 1500 10.6.9/24 testhost 170548881 245601 687976 0 0
lo0 8232 127 localhost 7530982 0 7530982 0 0
Example 2: Displaying Statistics for a Specific Protocol
The following example shows how snmpnetstat displays statistics for a
specific protocol.
% snmpnetstat-v 2c -c public -P tcp testhost
Active Internet (tcp) Connections
Proto Local Address Foreign Address (state)
tcp *.echo *.* LISTEN
tcp *.discard *.* LISTEN
tcp *.daytime *.* LISTEN
tcp *.chargen *.* LISTEN
tcp *.ftp *.* LISTEN
tcp *.telnet *.* LISTEN
tcp *.smtp *.* LISTEN
EXIT STATUS
0
Successful completion.
1
A usage syntax error. A usage message is displayed.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
┌─────────────────────────────┬─────────────────────────────┐
│ ATTRIBUTE TYPE │ ATTRIBUTE VALUE │
├─────────────────────────────┼─────────────────────────────┤
│Availability │SUNWsmcmd │
├─────────────────────────────┼─────────────────────────────┤
│Interface Stability │External │
└─────────────────────────────┴─────────────────────────────┘
SEE ALSOiostat(1M), netstat(1M), snmpcmd(1M), vmstat(1M), attributes(5)SunOS 5.10 20 Jan 2004 snmpnetstat(1M)