NG_PATCH(4) BSD Kernel Interfaces Manual NG_PATCH(4)NAMEng_patch — trivial mbuf data modifying netgraph node type
SYNOPSIS
#include <netgraph/ng_patch.h>
DESCRIPTION
The patch node performs data modification of packets passing through it.
Modifications are restricted to a subset of C language operations on
unsigned integers of 8, 16, 32 or 64 bit size. These are: set to new
value (=), addition (+=), subtraction (-=), multiplication (*=), division
(/=), negation (= -), bitwise AND (&=), bitwise OR (|=), bitwise eXclu‐
sive OR (^=), shift left (<<=), shift right (>>=). A negation operation
is the one exception: integer is treated as signed and second operand
(the value) is not used. There may be several modification operations,
they are all applied to a packet sequentially in order they were speci‐
fied by user. Data payload of packet is viewed as array of bytes, with
zero offset corresponding to the very first byte of packet headers, and
length bytes beginning from offset are taken as a single integer in net‐
work byte order.
HOOKS
This node type has two hooks:
in Packets received on this hook are modified according to rules
specified in config and then forwarded to out hook, if it exists
and connected. Otherwise they are reflected back to the in hook.
out Packets received on this hook are forwarded to in hook without
any changes.
CONTROL MESSAGES
This node type supports the generic control messages, plus the following:
NGM_PATCH_SETCONFIG (setconfig)
This command sets the sequence of modify operations that will be
applied to incoming data on a hook. The following struct
ng_patch_config must be supplied as an argument:
struct ng_patch_op {
uint64_t value;
uint32_t offset;
uint16_t length; /* 1,2,4 or 8 bytes */
uint16_t mode;
};
/* Patching modes */
#define NG_PATCH_MODE_SET 1
#define NG_PATCH_MODE_ADD 2
#define NG_PATCH_MODE_SUB 3
#define NG_PATCH_MODE_MUL 4
#define NG_PATCH_MODE_DIV 5
#define NG_PATCH_MODE_NEG 6
#define NG_PATCH_MODE_AND 7
#define NG_PATCH_MODE_OR 8
#define NG_PATCH_MODE_XOR 9
#define NG_PATCH_MODE_SHL 10
#define NG_PATCH_MODE_SHR 11
struct ng_patch_config {
uint32_t count;
uint32_t csum_flags;
struct ng_patch_op ops[];
};
The csum_flags can be set to any combination of CSUM_IP,
CSUM_TCP, CSUM_SCTP and CSUM_UDP (other values are ignored) for
instructing the IP stack to recalculate the corresponding check‐
sum before transmitting packet on output interface. The ng_patch
node does not do any checksum correction by itself.
NGM_PATCH_GETCONFIG (getconfig)
This control message obtains current set of modify operations,
returned as struct ng_patch_config.
NGM_PATCH_GET_STATS (getstats)
Returns node statistics as a struct ng_patch_stats.
NGM_PATCH_CLR_STATS (clrstats)
Clear node statistics.
NGM_PATCH_GETCLR_STATS (getclrstats)
This command is identical to NGM_PATCH_GET_STATS, except that the
statistics are also atomically cleared.
SHUTDOWN
This node shuts down upon receipt of a NGM_SHUTDOWN control message, or
when all hooks have been disconnected.
EXAMPLES
The ng_patch node allows to modify TTL and TOS/DSCP fields in IP packets.
Suppose you have two adjacent simplex links to remote network (e.g.
satellite), so that the packets expiring in between will generate
unwanted ICMP-replies which have to go forth, not back. Thus you need to
raise TTL of every packet entering link link by 2 to ensure the TTL will
not reach zero there. So you setup ipfw(8) rule with netgraph action to
inject packets going to other end of simplex link by the following
ngctl(8) script:
/usr/sbin/ngctl -f- <<-SEQ
mkpeer ipfw: patch 200 in
name ipfw:200 ttl_add
msg ttl_add: setconfig { count=1 csum_flags=1 ops=[ \
{ mode=2 value=3 length=1 offset=8 } ] }
SEQ
/sbin/ipfw add 150 netgraph 200 ip from any to simplex.remote.net
Here “ttl_add” node of type ng_patch configured to add (mode
NG_PATCH_MODE_ADD) a value of 3 to a one-byte TTL field, which is 9th
byte of IP packet header.
Another example would be two consecutive modifications of packet TOS
field: say, you need to clear the IPTOS_THROUGHPUT bit and set the
IPTOS_MINCOST bit. So you do:
/usr/sbin/ngctl -f- <<-SEQ
mkpeer ipfw: patch 300 in
name ipfw:300 tos_chg
msg tos_chg: setconfig { count=2 csum_flags=1 ops=[ \
{ mode=7 value=0xf7 length=1 offset=1 } \
{ mode=8 value=0x02 length=1 offset=1 } ] }
SEQ
/sbin/ipfw add 160 netgraph 600 ip from any to any not dst-port 80
This first does NG_PATCH_MODE_AND clearing the fourth bit and then
NG_PATCH_MODE_OR setting the third bit.
In both examples the csum_flags field indicates that IP checksum (but not
TCP or UDP checksum) should be recalculated before transmit.
Note: one should ensure that packets are returned to ipfw after process‐
ing inside netgraph(4), by setting appropriate sysctl(8) variable:
sysctl net.inet.ip.fw.one_pass=0
SEE ALSOnetgraph(4), ng_ipfw(4), ngctl(8)HISTORY
The ng_patch node type was implemented in FreeBSD 8.1.
AUTHORS
Maxim Ignatenko ⟨gelraen.ua@gmail.com⟩. This manual page was written by
Vadim Goncharov ⟨vadimnuclight@tpu.ru⟩.
BUGS
Node blindly tries to apply every patching operation to each packet
(except those which offset if greater than length of the packet), so be
sure that you supply only the right packets to it (e.g. changing bytes in
the ARP packets meant to be in IP header could corrupt them and make your
machine unreachable from the network).
!!! WARNING !!!
Output path of the IP stack assumes correct fields and lengths in the
packets - changing them by mistake to incorrect values can cause unpre‐
dictable results including kernel panics.
BSD June 9, 2010 BSD