dragonfly hardware description

DragonFly dragonfly.polarhome.com 5.2-RELEASE DragonFly v5.2.2.2.g17d386-RELEASE #0: Wed Jul 18 18:18:42 CEST 2018     root@dragonfly.polarhome.com:/usr/obj/usr/src/sys/X86_64_GENERIC  x86_64

Copyright (c) 2003-2018 The DragonFly Project.
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
DragonFly v5.2.2.2.g17d386-RELEASE #0: Wed Jul 18 18:18:42 CEST 2018
    root@dragonfly.polarhome.com:/usr/obj/usr/src/sys/X86_64_GENERIC
acpi_hpet: frequency 14318180
Using cputimer HPET for TSC calibration
Timer latency (in TSC ticks): 13379 min=9503 max=17008
TSC invariant clock: 3059228592 Hz
CPU: Intel(R) Xeon(R) CPU           X5675  @ 3.07GHz (3059.23-MHz K8-class CPU)
  Origin = "GenuineIntel"  Id = 0x206c2  Stepping = 2
  Features=0x1783fbff
  Features2=0x298220b
  AMD Features=0x28100800
  AMD Features2=0x1
real memory  = 1072233472 (1022 MB)
avail memory = 962695168 (918 MB)
LAPIC latency (in TSC ticks): 12516 min: 8176 max: 16314
lapic: divisor index 0, frequency 500009443 Hz
srat_probe: can't locate SRAT
SMI Frequency (worst case): 8196 Hz (122 us)
Initialize MI interrupts
TSC: cputimer freq 95600893, shift 5
machdep.spectre_mitigation=-1: IBRS=NOSUPPORT, IBPB=NOSUPPORT
VMM: VMX is not supported by this Intel CPU
machdep.meltdown_mitigation enabled to protect against (mostly Intel) meltdown bug
system call performance will be impacted
wdog: In-kernel automatic watchdog reset enabled
kbd1 at kbdmux0
md0: Malloc disk
interrupt uses mplock: swi_taskq
ACPI: RSDP 0x00000000000E0000 000024 (v02 VBOX  )
ACPI: XSDT 0x000000003FFF0040 00004C (v01 VBOX   VBOXXSDT 00000001 ASL  00000061)
ACPI: FACP 0x000000003FFF0110 0000F4 (v04 VBOX   VBOXFACP 00000001 ASL  00000061)
ACPI: DSDT 0x000000003FFF0530 002325 (v02 VBOX   VBOXBIOS 00000002 INTL 20180105)
ACPI: FACS 0x000000003FFF0240 000040
ACPI: APIC 0x000000003FFF0280 000054 (v02 VBOX   VBOXAPIC 00000001 ASL  00000061)
ACPI: HPET 0x000000003FFF02E0 000038 (v01 VBOX   VBOXHPET 00000001 ASL  00000061)
ACPI: MCFG 0x000000003FFF0320 00003C (v01 VBOX   VBOXMCFG 00000001 ASL  00000061)
ACPI: SSDT 0x000000003FFF0360 0001CC (v01 VBOX   VBOXCPUT 00000002 INTL 20180105)
sc0:  on motherboard
sc0: VGA <16 virtual consoles, flags=0x300>
cryptosoft0:  on motherboard
acpi0:  on motherboard
ACPI: Executed 1 blocks of module-level executable AML code
ACPI: 2 ACPI AML tables successfully acquired and loaded
ACPI FADT: SCI testing interrupt mode ...
ACPI FADT: SCI select level/low
acpi0: Power Button (fixed)
acpi0: Sleep Button (fixed)
acpi_hpet0:  iomem 0xfed00000-0xfed003ff irq 8,0 on acpi0
acpi_timer0 on acpi0
cpu0:  on acpi0
cpu_cst0:  on cpu0
acpi_acad0:  on acpi0
pcib0:  port 0xcf8-0xcff on acpi0
pci0:  on pcib0
vgapci0:  mem 0xe0000000-0xe0ffffff irq 18 at device 2.0 on pci0
vgapci0: Boot video device
em0:  port 0xd000-0xd007 mem 0xe1000000-0xe101ffff irq 19 at device 3.0 on pci0
em0: Using 256 TX descriptors instead of 512!
em0: Using 256 RX descriptors instead of 512!
em0: MAC address: 08:00:27:ae:c2:f3
pci0:  (vendor 0x80ee, dev 0xcafe) at device 4.0 irq 20
pci0:  (vendor 0x8086, dev 0x7113) at device 7.0 irq 23
isab0:  at device 31.0 on pci0
isa0:  on isab0
atapci0:  port 0xd040-0xd04f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 31.1 on pci0
ata0:  on atapci0
interrupt uses mplock: ata0
ad0: 512000MB  at ata0-master UDMA100
ohci0:  mem 0xe1804000-0xe1804fff irq 23 at device 31.4 on pci0
usbus0 on ohci0
atkbdc0:  port 0x64,0x60 irq 1 on acpi0
atkbd0:  irq 1 on atkbdc0
kbd0 at atkbd0
usbus0: 12Mbps Full Speed USB v1.0
ugen0.1:  at usbus0
uhub0:  on usbus0
psm0:  irq 12 on atkbdc0
interrupt uses mplock: psm0
psm0: model IntelliMouse Explorer, device ID 4
ACPI: Enabled 2 GPEs in block 00 to 07
aesni0:  on motherboard
padlock0: No ACE support.
rdrand0: No RdRand support.
Freeing low dma reserve @ 0xfffff8007a200000
orm0:  at iomem 0xc0000-0xc7fff,0xe2000-0xe2fff on isa0
vga0:  at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sio0: can't drain, serial port might not exist, disabling
sio1: can't drain, serial port might not exist, disabling
hpt27xx: no controller detected.
CAM: Configuring 1 busses
CAM: finished configuring all busses
uhub0: 12 ports with 12 removable, self powered
Mounting root from hammer:serno/VBbeafa40c-83e01b34.s1d
HAMMER(ROOT) recovery check seqno=10f92a9e
HAMMER(ROOT) recovery range 30000000135abdb0-30000000135abdb0
HAMMER(ROOT) recovery nexto 30000000135abdb0 endseqno=10f92a9f
HAMMER(ROOT) mounted clean, no recovery needed
DMA space used: 72k, remaining available: 62936k
Mounting devfs
HAMMER(BUILD) recovery check seqno=0a9578b9
HAMMER(BUILD) recovery range 300000001eb66460-300000001edd4000
HAMMER(BUILD) recovery nexto 300000001eb66460 endseqno=0a958dd7
HAMMER(BUILD) recovery undo  300000001eb66460-300000001edd4000 (2546592 bytes)(RW)
HAMMER(BUILD) recovery complete
swap low/high-water marks set to 20968/31453

Filesystem                           Size   Used  Avail Capacity  Mounted on
ROOT                                 476G  4923M   472G     1%    /
devfs                               1024B  1024B     0B   100%    /dev
/dev/serno/VBbeafa40c-83e01b34.s1a  1022M   465M   475M    49%    /boot
BUILD                               19.5G  4139M  15.4G    21%    /build
/build/usr.obj                      19.5G  4139M  15.4G    21%    /usr/obj
/build/var.crash                    19.5G  4139M  15.4G    21%    /var/crash
/build/var.cache                    19.5G  4139M  15.4G    21%    /var/cache
/build/var.spool                    19.5G  4139M  15.4G    21%    /var/spool
/build/var.log                      19.5G  4139M  15.4G    21%    /var/log
/build/var.tmp                      19.5G  4139M  15.4G    21%    /var/tmp
tmpfs                                238M     0B   238M     0%    /tmp
procfs                              4096B  4096B     0B   100%    /proc

Vote for polarhome