NAME

amr — AMI MegaRAID PCI-SCSI RAID driver

SYNOPSIS

amr* at pci? dev ? function ?
scsibus* at amr?

DESCRIPTION

The amr driver provides support for LSI (formerly American Megatrends) MegaRAID Express, Elite and Enterprise family RAID controllers for SCSI and SATA, including models relabeled and sold by Dell, Hewlett-Packard, and Intel. Supported controllers include:

MegaRAID 320-1
MegaRAID 320-2
MegaRAID Series 418
MegaRAID Enterprise 1200 (Series 428)
MegaRAID Enterprise 1300 (Series 434)
MegaRAID Enterprise 1400 (Series 438)
MegaRAID Enterprise 1500 (Series 467)
MegaRAID Enterprise 1600 (Series 471)
MegaRAID Elite 1500 (Series 467)
MegaRAID Elite 1600 (Series 493)
MegaRAID Express 100 (Series 466WS)
MegaRAID Express 200 (Series 466)
MegaRAID Express 300 (Series 490)
LSI MegaRAID SCSI 320-0X, 320-2X, 320-4X
LSI MegaRAID SCSI 320-1E, 320-2E
LSI MegaRAID SATA 300-6x, 300-8x
Dell PERC
Dell PERC 2/SC
Dell PERC 2/DC
Dell PERC 4/Di
Dell PERC 4/SC
Dell PERC 4e/Si
HP NetRAID-1/Si
HP NetRAID-3/Si
HP Embedded NetRAID
Intel SRCU42X
Intel SRCU42E
Intel SRMOBU42E
Intel SRCS28X

DIAGNOSTICS

Driver initialisation/shutdown phase

amr%d: memory window not available
amr%d: I/O window not available: The PCI BIOS did not allocate resources necessary for the correct operation of the controller. The driver cannot attach to this controller.
amr%d: busmaster bit not set, enabling: The PCI BIOS did not enable busmaster DMA, which is required for the correct operation of the controller. The driver has enabled this bit and initialisation will proceed.
amr%d: can't allocate register window
amr%d: can't allocate interrupt
amr%d: can't set up interrupt
amr%d: can't allocate parent DMA tag
amr%d: can't allocate buffer DMA tag
amr%d: can't allocate scatter/gather DMA tag
amr%d: can't allocate s/g table
amr%d: can't allocate mailbox tag
amr%d: can't allocate mailbox memory: A resource allocation error occurred while initialising the driver; initialisation has failed and the driver will not attach to this controller.
amr%d: can't obtain configuration data from controller
amr%d: can't obtain product data from controller: The driver was unable to obtain vital configuration data from the controller. Initialisation has failed and the driver will not attach to this controller.
amr%d: can't establish configuration hook
amr%d: can't scan controller for drives: The scan for logical drives managed by the controller failed. No drives will be attached.
amr%d: device_add_child failed
amr%d: bus_generic_attach returned %d: Creation of the logical drive instances failed; attachment of one or more logical drives may have been aborted.
amr%d: flushing cache...: The controller cache is being flushed prior to shutdown or detach.

Operational diagnostics

amr%d: I/O beyond end of unit (%u,%d > %u): A partitioning error or disk corruption has caused an I/O request beyond the end of the logical drive. This may also occur if FlexRAID Virtual Sizing is enabled and an I/O operation is attempted on a portion of the virtual drive beyond the actual capacity available.
amr%d: polled command timeout: An initialisation command timed out. The initialisation process may fail as a result.
amr%d: bad slot %d completed: The controller reported completion of a command that the driver did not issue. This may result in data corruption, and suggests a hardware or firmware problem with the system or controller.
amr%d: I/O error - %x: An I/O error has occurred.